Complete Motorcycle Builds and Custom Work:

Off and on throughout our tenure we have been asked to work on complete motorcycles and perform everything from routine maintenance to serious custom fabrication/creation work. This was never an advertised service line of business for us. But starting in 2025 we are opening this up to the business public. Give us a call to discuss your specific project and we’ll try to make your dream a reality.

Some past builds/collaborations:

Brian’s 1984 RZ350:
  • Full Phase III Tuned 4-Mil Stroker engine with 35 PWK Air Stryker carbs, Wicked Motorsports HP stroker pipes
  • Rebuild the entire brake system with repainting
  • Pulled wheels and had them powder coated and then replaced with new wheel bearings and Avon tires
  • Blasted and repainted the OEM rotors
Doug’s 1984 RZ500:
  • Performed Phase II Tune and Restoration to the engine
  • WP 28mm Flatslide Carb Kit Installed and Tuned
  • Installed 2001 Yamaha R1 Forks w/Custom RZ steering stem installed in the R1 triple clamps
  • Ordered and Installed modified 08-15 Yamaha R6 Swingarm
  • Custom fit 2001 Yamaha R1 rear wheel in R6 swingarm
  • Custom Speigler brakelines
  • Custom Rearset mounts
  • CRG Rearsets
  • Jim Lomas Stainless Jolly Moto exhaust fitted with Custom Hanger Assemblies
  • Koso GP2 Dash Cluster Installed
  • WP Lithium Battery box installed

Rene’s 1985 RZ500:
  • NK Racing Billet Triple Clamps for 08-15 Yamaha R6 Forks
  • 08-15 Yamaha R6 Front and Rear Wheels Powdercoated Mistic Gold, New Wheel Bearings Installed
  • 08-15 Yamaha R6 Rear Swingarm Upgraded to Fit the RZ500 Chassis by NK Racing
  • Nitron Rear Shock w/Remote Reservoir (185kg)
  • 08-15 Yamaha R6 Forks Fully Rebuilt
  • 08-15 Yamaha R6 Fork Top Caps Replaced
  • Koso RX-2 Integrate Dash Cluster w/2nd RZ500 OEM cluster wiring loom soldered together
  • Koso GPS Signal Converter for Speedometer
  • Wilson Performance Custom Battery Box and Strap
  • Anti-Gravity 4 cell Lithium Battery
  • 520 DID X-Ring Gold Chain and Rebel Gears Sprockets (17 Front/42 Rear)
  • RZ350 Coolant Reservoir w/Billet Custom Mounting Bracket
  • Custom Length Spiegler Brake Lines and Fittings
  • TZR250 3MA Tail-light Custom Mounting and Fit
  • New Yamaha Petcock
  • WD Tail-Light Integrator Kit with All Soldered Connectors and Waterproof Connectors
  • RZV500 Shifter and Rear Brake Levers Mirror Polished
  • OEM Rearset Brackets Highly Modified and Repainted
  • OEM Kickstarter Mirror Polished
  • Samco Silicone Hose & Clamp Kit Installed
  • Shifter Rubber Knob Replaced
  • Shifter Linkage Rubber Covers Replaced
  • New Footpeg Buttons
  • New Aftermarket Belly Pan
  • New Solo-seat Bobbins, Properly Modified to Use Cotter Pins for Retention
  • Complete RZ500 Decal Set
  • Rear Side Panels and Tail Section Cut Down and Custom Tail Fastener Brackets Epoxy Installed
  • Rear Side Panel OEM Heat Shielding Modified to Fit modified Side Panels and Reinstalled w/Aluminum Heat Tape
  • Full Body Repaint
  • New Old Stock Seat Latch Lock
  • New Nissin Remote Front Brake Master Cylinder
  • Custom Mirror Polished Aluminum Front Master Cylinder Reservoir Bracket
  • ASV Front Brake and Clutch Levers (Yamaha R6)
  • New R6 Clutch Pirch
  • Custom Cable Spacer for the RZ to R6 Clutch Pirch
  • Aftermarket Front & Rear Brake Rotors
  • New Front Rotor Bolts OEM
  • New R6 Rear Master Cylinder (Brembo)
  • Custom Rear Master Cylinder Reservoir Mounting Bracket
  • New Aftermarket Large Capacity Aluminum Radiator
  • Flush Mount Front Turn Signals with Custom Pinch Type Mounting Hardware
  • Custom Mirror Polished Aluminum Trunk Plate